Mission Boat Gear Delta - Universal Surf Gate!

[Lsufreak10]

Iceman,

What did you use to connect the seaboard to the suction. Where did you get those shelve holders at

[jbgp1200]

They have them at Lowes. I have had 4 of them for 6 months and had every intent of building some shelves with them. However they may be used for additional R&D.


Sent from my iPhone using Tapatalk

[ICEMANFTR]

Iceman,

What did you use to connect the seaboard to the suction. Where did you get those shelve holders at

They have them at Lowes. I have had 4 of them for 6 months and had every intent of building some shelves with them. However they may be used for additional R&D.


Sent from my iPhone using Tapatalk

Exacto mondo!


Sent from my iPhone using Tapatalk

[Lsufreak10]

and yalls home made version works well and cleans up wake?

[ICEMANFTR]

and yalls home made version works well and cleans up wake?

Yep



Sent from my iPhone using Tapatalk

[Doublewide450x]

so what boat is that whats the settings ballast mods etc or is that just stock with the homemade system

Thanks

Looks awesome

[ICEMANFTR]

so what boat is that whats the settings ballast mods etc or is that just stock with the homemade system

Thanks

Looks awesome

2013 Moomba LSV 500 in each rear locker and around 700 up front. Just driver in boat. Didn't go sacked out because my rub rail seal is bad and getting repairs today. But it was awesome even at that weight with so much push.

This system here.


Sent from my iPhone using Tapatalk

[UNSTUCK]

Just a thought, grab some vacuum caps to put over the threads of all your screws, or cut the extra threads off. Just to help get rid of sharp edges.

My HOD showed up today. Should have it made this weekend.

[UNSTUCK]

Iceman, what is the length of the spacers you used to get the (10*?) angle? I assume you mounted the tab as far to the rear as you could? Did you try mounting it at different heights on the side of the boat? Close to the rub rail or as far under the water as you could reach?

[ICEMANFTR]

Iceman, what is the length of the spacers you used to get the (10*?) angle? I assume you mounted the tab as far to the rear as you could? Did you try mounting it at different heights on the side of the boat? Close to the rub rail or as far under the water as you could reach?

1.5" nylon spacer. We did try a few heights and pretty close to stern. Mine has body lines that make me limited on suction points, but it stuck out of water slightly until take off. The farther in the less spray. There is a spot completely submerged I can try, but don't know if it's necessary and my be harder to apply and keep on?...


Sent from my iPhone using Tapatalk

[culrich77]

So I threw this guy together for less than $30 bucks, bought a cutting board at Wal-Mart and it even has a handle, does the Delta have that, ha!! My question is for those of you that have attempted this mod is my board too big? It measures 11 inches tall by 14 inches long, I'm thinking I may need to cut it down.
IMG_3318.jpgIMG_3317.jpg

[Captainkurk72]

I vote that the "Chop it like its hot" goes on the outside for everyone to see


Sent from my iPhone using Tapatalk

[ICEMANFTR]

So I threw this guy together for less than $30 bucks, bought a cutting board at Wal-Mart and it even has a handle, does the Delta have that, ha!! My question is for those of you that have attempted this mod is my board too big? It measures 11 inches tall by 14 inches long, I'm thinking I may need to cut it down.
[ATTACH]43122[/ATTACH][ATTACH]43123[/ATTACH]

Haha I love it. I would say try it. Although it might be too aggressive in size. My biggest one was roughly 8 1/2 wide by 9.5 tall.


Sent from my iPhone using Tapatalk

[UNSTUCK]

Culrich, When will yours be in the water? I have a similar sized Walmart cutting board and am wondering about cutting it down or not. I like having a handle on it like yours, but wonder if it's too big.

[Yankees39]

Are those shelf brackets y'all are using to bolt onto the board and suction cups? And I guess I can just pick them up at Home Depot or lowes?