06 24 V - Surf/Sac Advice

[pdhj1990]

Do we need any additional weight for our 24V beyond the Enzo sac? The wake looks pretty good, however any additional input is greatly appreciated. Also, any input on Taps setting is equally valuable.
Paul

[MooseX]

maybe some weight on the swim step. Duffy runs a sh*tload on his 24v step' and I've got 2 150 bricks on my 24V's platform. I've also got an Enzo in each locker + 2 300's up front.. but I don't use them and the wave is pretty darn good. So with just the enzo, 2 bricks and a couple of people on the surf side the wave is great

Taps I'm usually at 3 give or take a little bit..I like the nice long wave it gives me. I'm talking both sides now..Goofy and Port waves are both real clean

[pdhj1990]

MooseX,

I'm going to take a few pics of the wake this Saturday with the Enzo and a few folks in the back. I'll post the pics and would appreciate your additional input.

Thanks.

[duffymahoney]

I run a custom 1800+ pound enzo sac. Plus dual 250 sacs in the bow plus 250 on the swim deck. Wave is big and long. It's actually nicer then this picture shows now, we have been dialing things in. I run taps at 2.

[Bad05]

I currently run a 1500 in the rear, 500 in the front, 400 in the center and place two 155s where needed. My TAPS is currently on the blink and stuck at 8 so it's a deep, fast pocket but I would normally run it at 3-5.

[pdhj1990]

Is this what you guys use in the bow:

http://www.wakemakers.com/fly-high-i...d-bow-sac.html

[duffymahoney]

I am actually using 2 fly high side sacs. My original idea was to only fill one side. I now fill both.

[pdhj1990]

I forgot to say this in my earlier reply, YOUR BOAT THROWS A VERY SWEET WAKE

Is this what your talking about? These seem too large, while the The Fly High Pro X Series Integrated Bow Sac seems right for the area. Thoughts?

[MooseX]

Duffy you need to show your 'real wave'...that one looks more like my crummy little wave

I'm runnin' twin 'Nautique' sacs from wavemakers. I think they're 300's. It's a tight fit but that's what Jason told me to use.

They're connected to the same pump but with only one vent (out the port side just below the windshield).

[pdhj1990]

I'm still using the portable Fly High Pro X Tsunami Ballast Pumps. I'll have to wait until winter to have pumps installed in the boat.

I'm still a little confused on the bow sacs. Will The Fly High Pro X Series Open Bow Sac work? I don't want to over think this stuff, however you guys have far more experience on this matter.

I just want a sweet wake. Thanks.

[chpthril]

I'm still using the portable Fly High Pro X Tsunami Ballast Pumps. I'll have to wait until winter to have pumps installed in the boat.

I'm still a little confused on the bow sacs. Will The Fly High Pro X Series Open Bow Sac work? I don't want to over think this stuff, however you guys have far more experience on this matter.

I just want a sweet wake. Thanks.

The W706 open bow sac fills to 1K and would sit on the seats, so no peeps up front when in use.

If someone is not going to run dual pumps for the bow in order to fill the surf side sac only, then there is not an advantage to using dual sacs over the W711 integrated bow sac IMO.

[duffymahoney]

My idea was to only weight the surf side. On my last boat that was key to a good wave.

[pdhj1990]

Thanks guys. I'll call wakemakers to determine what side sac will fit under the bow seat on the surf side.

Again, thanks.

[Dan and Christy]

PDHJ - Do yourself a favor and call Mike (chpthril), he'll get you setup with exactly what you need.

[duffymahoney]

Gosh I like having both. But I guess if I was to do it again I would have just gone with a bow sac. If I could get more weight on just surf side in the bow then that would be better.