Announcement

Collapse
No announcement yet.

wet sounds xxx12 amp questions

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    wet sounds xxx12 amp questions

    i have a syn2 powering pro 60's on my tower and the HU powering 4 in boat xs 650's, i just picked up D2 xxx12 sub

    i was thinking to get a syn6 and power the in boats and tower and use the syn2 to power the xxx 12 will it be enough is the question,

    09 Z1
    Tags: None
    #2
    You will not be disappointed with that setup at all.
    Mikes Liquid Audio: Knowledge Experience Customer Service you can trust-KICKER WetSounds ACME props FlyHigh Custom Ballast Clarion LiquidLumens LEDs Roswell Wave Deflector And More

    Comment

      #3
      I would agree with Chp, IF you're content with a super-nice, but not wild system. It will sound awesome, it just won't ROCK the lake like maxxing the wattage of the speakers will.


      At "only" 700 watts to the XXX, you will be leaving a lot of potential on the table with that speaker. If you can afford it, I would get a SYN1 for the XXX. Obviously, I have no idea on your $$$ situation....
      Also, the inboats can handle much more than 60 watts. IF you're looking to really rock. Depends on what you want out of the system.
      Other than that, Mrs. Lincoln, how was the play?

      Comment

        #4
        thanx for the help guys

        i only have a single battery , i guess i'am going to be upgrading that to any suggetions on battery upgrade or type i should use!

        Comment

          #5
          Z1, the SYN-2 mono will do 700x1 at 4 ohms. This is solid power on the XXX if you build the slot loaded enclosure. The slot loaded enclosures offer more output and you can get away with a bit less power. In the sealed, the XXX needs more power. Which would be the SYN-1. So Jason is correct, with the SYN-2 it will pound and sound great. With the SYN-1, it is going to be just more in terms of raw power.

          But if your budget does not allow. The SYN-2 on the XXX wired in series so a 4 ohm load for 700x1 is going to be very nice

          Check out XS Power for the batts. www.4xspower.com


          Tim
          Wet Sounds

          Comment

            #6
            thanx tim for the advice,

            the Z1 has a small storage area under the helm , i'am going to cut a square hole in the wall.......there's just no other way to get a box in there , i found a box made by atrend (slot ported) the dims are 14w 16h and 18 deep , you think this will be ok! that's the best i think i can do!

            Comment

              #7
              Originally posted by Z1 guy View Post
              thanx tim for the advice,

              the Z1 has a small storage area under the helm , i'am going to cut a square hole in the wall.......there's just no other way to get a box in there , i found a box made by atrend (slot ported) the dims are 14w 16h and 18 deep , you think this will be ok! that's the best i think i can do!
              Whats the box made of? If it's marketed as "car audio", it's probably carpeted MDF and will fall apart in a season. Your best bet is to make a custom enclosure and coat it with resin.
              Mikes Liquid Audio: Knowledge Experience Customer Service you can trust-KICKER WetSounds ACME props FlyHigh Custom Ballast Clarion LiquidLumens LEDs Roswell Wave Deflector And More

              Comment

                #8
                they have a slammer series ,that is coated on the outside , same stuff they use for truck beds, the box is made of 3/4 hardwood mdf with 1 inch thick face, just trying to save time boatin season is near......lol

                Comment

                Previous template Next
                Working...
                X