Im lost without the PW thread!!!!

[bryce2320]

Now I have to figure out where to mount the 2nd pair of rev 10s. I'd like to mount them on the front bar tucked up close to where it curves around in the corner

[chpthril]

So I go look at this boat this morning. Customer said the installer never came back to finish, sub doesnt work and it sounds like @$$ when you turn it up.

As soon as I peeled back the cover, I knew who did by the gear installed. But get a load of this sub box: raw MDF covered in automotive trunk liner, sitting directly on the floor of an enclosed locker, speaker wire poked through hole in the back. Oh, it gets better Its ported. The port is 3 or 4 inch PVC painted on the inside and the top .5" of a stainless steel cup holder sawed off as a trim ring

I'll post a pic later as i need to cover the sub brand as they do not deserve to me shown in this way

[bryce2320]

Fedex shows theyll b here tomorrow

[bryce2320]

So I go look at this boat this morning. Customer said the installer never came back to finish, sub doesnt work and it sounds like @$$ when you turn it up.

As soon as I peeled back the cover, I knew who did by the gear installed. But get a load of this sub box: raw MDF covered in automotive trunk liner, sitting directly on the floor of an enclosed locker, speaker wire poked through hole in the back. Oh, it gets better Its ported. The port is 3 or 4 inch PVC painted on the inside and the top .5" of a stainless steel cup holder sawed off as a trim ring

I'll post a pic later as i need to cover the sub brand as they do not deserve to me shown in this way

How else would you do it

[halfwatt]

So I go look at this boat this morning. Customer said the installer never came back to finish, sub doesnt work and it sounds like @$$ when you turn it up.

As soon as I peeled back the cover, I knew who did by the gear installed. But get a load of this sub box: raw MDF covered in automotive trunk liner, sitting directly on the floor of an enclosed locker, speaker wire poked through hole in the back. Oh, it gets better Its ported. The port is 3 or 4 inch PVC painted on the inside and the top .5" of a stainless steel cup holder sawed off as a trim ring

I'll post a pic later as i need to cover the sub brand as they do not deserve to me shown in this way

Wow, talk about shoddy work!

[chpthril]

So I go look at this boat this morning. Customer said the installer never came back to finish, sub doesnt work and it sounds like @$$ when you turn it up.

As soon as I peeled back the cover, I knew who did by the gear installed. But get a load of this sub box: raw MDF covered in automotive trunk liner, sitting directly on the floor of an enclosed locker, speaker wire poked through hole in the back. Oh, it gets better Its ported. The port is 3 or 4 inch PVC painted on the inside and the top .5" of a stainless steel cup holder sawed off as a trim ring

I'll post a pic later as i need to cover the sub brand as they do not deserve to me shown in this way

never mind, I had one thats zoomed in on just the port

[chpthril]

Wow, talk about shoddy work!

8ga cable about a 20ft run is feeding a 600W 2 chnl, an automotive fuse holder in the bilge for the amps. Amps and head-unit are running off different batteries. The in-boats are running full-pass.

I hate re-dues like this.

[halfwatt]

Car's done. Time to go back to work.

[chpthril]

How else would you do it

Well, the only thing done right was the sub choice The total execution was wrong

[dingleberry]

So I go look at this boat this morning. Customer said the installer never came back to finish, sub doesnt work and it sounds like @$$ when you turn it up.

As soon as I peeled back the cover, I knew who did by the gear installed. But get a load of this sub box: raw MDF covered in automotive trunk liner, sitting directly on the floor of an enclosed locker, speaker wire poked through hole in the back. Oh, it gets better Its ported. The port is 3 or 4 inch PVC painted on the inside and the top .5" of a stainless steel cup holder sawed off as a trim ring

I'll post a pic later as i need to cover the sub brand as they do not deserve to me shown in this way

Hmmm...a little worse than the install done by my dealer, but not by much.

My sub's "port" was simply a 2" hole drilled in the box

[Bruizza]

4 Rev 10s can get you one of these Bryce.

[halfwatt]

8ga cable about a 20ft run is feeding a 600W 2 chnl, an automotive fuse holder in the bilge for the amps. Amps and head-unit are running off different batteries. The in-boats are running full-pass.

I hate re-dues like this.

why not put the fuse in the bilge...there's all that room, it's a straight shot and it's not like there's ever any moisture down there!

[halfwatt]

4 Rev 10s can get you one of these Bryce.

[konajay]

The boats getting 15% tint Tuesday for 250$. And that's with him taking the top frame off so there's no gap

Killer deal

[konajay]

So I guess the management at the gas station has decided to not let them park there

Go tell them that's the only reason you bought your gas there