Im lost without the PW thread!!!!

[skippabcool]

x2 on exit rows.

x3

I used get them all the time but now rarely get them.

[skippabcool]

Can one of you 22ve hoes with your boat at home measure and see if the bow sacs in this link will fit?

http://www.wakemakers.com/fly-high-p...m-bag-005.html

Are these the measurements your after? 50" x 10" x 12"

[majestic]

When the kiddos take a nap I'll try to get out to the shop and check it out for you Maj

Thanks Lance

[skippabcool]

I got the batteries in and cleaned up the wiring a bit

[majestic]

Are these the measurements your after? 50" x 10" x 12"

Yessir.

[skippabcool]

Got to test the heater motor that I replaced. Heater is now good as new.

[majestic]

I got the batteries in and cleaned up the wiring a bit

Skippa do you run drain and vents to the opposite side or are you using check valves?

[majestic]

Got to test the heater motor that I replaced. Heater is now good as new.

I love the my heater Have you seen the blanket that you plug the heater hose into?

http://www.bakesonline.com/detail.aspx?ID=858

[skippabcool]

Can one of you 22ve hoes with your boat at home measure and see if the bow sacs in this link will fit?

http://www.wakemakers.com/fly-high-p...m-bag-005.html

I measured 53" to the tip but usable is about 51".
Side to side is about 19" but at 16" is what has the depth.
Depth is 10".

We can see if lance gets something different.

[skippabcool]

Skippa do you run drain and vents to the opposite side or are you using check valves?

I ran them to the opposite side and combined them with a check valve at the tee on the vent line.

[skippabcool]

I love the my heater Have you seen the blanket that you plug the heater hose into?

http://www.bakesonline.com/detail.aspx?ID=858

I just did now.

[mls6722]

Can one of you 22ve hoes with your boat at home measure and see if the bow sacs in this link will fit?

http://www.wakemakers.com/fly-high-p...m-bag-005.html

Majestic, I have the W711 in there and the measurement of that bag is :
Body Dimensions: L20" x W29" x H12"
Arm Dimensions: L32" x W12" x H12"

It doesn't get nearly full, but fits nicely in the bow.

i was looking at those separate bow sacs - If you don't get them, I might.

[skippabcool]

I am about to drill the holes in the rear locker dividers but wanted to ask a couple of questions first. On the starboard side I can not put the drain right in the middle because of the taps motor and heater motor. It would only be about 8.5 inches from the side of the boat. Is that an issue? For the v drive locker sac, 400#, I don't see an issue. It would be more for the custom sac if I move it over there.

I want to do the drain quick connects like this picture. Should I do them so that they can slide all the back or just enough that it barely sticks out. Where I have already cut the hose I will not be able to pull them out much. Thoughts?

[majestic]

Majestic, I have the W711 in there and the measurement of that bag is :
Body Dimensions: L20" x W29" x H12"
Arm Dimensions: L32" x W12" x H12"

It doesn't get nearly full, but fits nicely in the bow.

i was looking at those separate bow sacs - If you don't get them, I might.

I had a bow sac I bought from CHP but sold it thinking I would never need it. Now that I am going to get some more weight in he back I may be able to put a little up front.

Don't wait on me if it works for you pull the trigger. I dont think it will be any better than what you have though,

[majestic]

I am about to drill the holes in the rear locker dividers but wanted to ask a couple of questions first. On the starboard side I can not put the drain right in the middle because of the taps motor and heater motor. It would only be about 8.5 inches from the side of the boat. Is that an issue? For the v drive locker sac, 400#, I don't see an issue. It would be more for the custom sac if I move it over there.

I want to do the drain quick connects like this picture. Should I do them so that they can slide all the back or just enough that it barely sticks out. Where I have already cut the hose I will not be able to pull them out much. Thoughts?

Mine is in the center but I only have the taps tank back there. My sac never fills straight anyway so it may not matter much. Who cares anyway your not goofy Make the best wake for you and everyone else can just be happy to get a pull

I think on mine I have about 3 inches of hose off the drain pump and the quick connect sticks out a inch or so from the wall.