stainless rub rail '08RZ2

[chpthril]

no name on bag, but the bag is white and the valves are orange. The valves have Made in China on them.

If I remember right, the Tige front ballast sac (the white one) uses garden hose threads. CP3 got a sac as part of his "pimp my Tige", and needed fittings and I believe he found what he needed at the hardware store.

[chpthril]

1. the cruise control does not seem to work. It might be user error.

When you turn on the SpeedSet's master "ON/OFF" switch on the dash, did the "Set speed" and "Actual speed" display on the LCD Screen? From there, you can either use the "up" button to set your ride speed before you accelerate, or you can accelerate to your ride speed, press the "Set" button in the center of the oval pad. Once you press the "set" button, the set speed should pop up in the display, and should match the actual speed in the display.

[lincdarrow]

I turned the swith on. Yhe Set Speed is in the upper right and the actual speed is centered large on the bottom of the screen (great display). I pushed the "up button" and nothing happens to the 'Set Speed' screen, it justs stays at 0.0. I also tried the other recommended way to get to speed and hit the "set" button and nothing happens. I wonder if there is a fuse for the speed set? Of course if there was a fuse then when I swiched the master rocker switch on then nothing would happen. The set speed never left 0.0 all weekend after numerous attemps.

I figure there will be a few bugs in any new boat with electronics.

Also at full throttle the depth finder goes to 997.0' when I back off a bit it comes back to reading depth, so I figure vibration os causing the depthfinder to lose itself.

[chpthril]

I turned the swith on. Yhe Set Speed is in the upper right and the actual speed is centered large on the bottom of the screen (great display). I pushed the "up button" and nothing happens to the 'Set Speed' screen, it justs stays at 0.0. I also tried the other recommended way to get to speed and hit the "set" button and nothing happens. I wonder if there is a fuse for the speed set? Of course if there was a fuse then when I swiched the master rocker switch on then nothing would happen. The set speed never left 0.0 all weekend after numerous attemps.

I figure there will be a few bugs in any new boat with electronics.

Also at full throttle the depth finder goes to 997.0' when I back off a bit it comes back to reading depth, so I figure vibration os causing the depthfinder to lose itself.

I would double check just to make sure the plug is fully seated to the back of the Speed-Set pad, and also on the master switch. Did the little back-lite light up on the rocker switch when you flipped it on?

Depth Finder = Air bubbles going across the pick-up. At WOT, the boats is barely in the water

[lincdarrow]

I do not remeber a light coming on. I will check when I go home at luch time.

[lincdarrow]

NO GOOD.
The light on the toggle switch does not come on. I started to pull the switch panel out and all of the wires appear to be connected well to the toggle switch.

All of the other toggle switches light up when switched.
Where do I go from here??

[larryueckert]

check the fuse panel and push all the fuse's in

[FacePlant]

I would check the fuse panel to make sure you are good there. If the fuses are all good, you might need a new switch....

[chpthril]

You will find that most of the non-essential components are protected with an in-line fuse V's a manual-reset breaker. If you lay on the floor and look up behind the dash, you will see numerous black plastic in-line fuse holders. You may be able to trace from the switch to the SpeedSet's fuse holder, but it may be easier to just check them all.

[lincdarrow]

all fuses are pushed in

[lincdarrow]

I love messing with spaghetti. laying on your back staring up at the wires with plastic falling back into your eyes always gives me a headache.

I hope I find it, it will be an easy fix.

[lincdarrow]

Here is the rig

IMG00119.jpg

[jake's02-22i]

really nice.

how do you like the tower? does it move around at all?

[lincdarrow]

I like it. The folding option is really nice. It fits in my garage.

It moved some when the racks were loaded and we were in 1'-2' chop, but nothing like my frineds Mastercraft x-30.

I am happy with it, and I like the looks a bit more that Tige's factory tower.

The Samson Speaker system / connection is awesome.

[jake's02-22i]

post up more pics when you get it all hooked up.