Looking for replacement trailer jack

[Bakes5]

Hey...I've been trying to replace my trailer jack for about 2 yrs. it officially died the other day and now requires a floor jack to lift it. Have not been able to find one the right size. I'm pretty sure it is 3.5" x 5". Anybody have a source for a replacement one? I would love to just mount a Fulton f2 up but don't have an adapter plate.

[talltigeguy]

I personally think the F2 is overrated, after having one. I think they got smart and now make one that does not require an adapter plate. I would go to Etrailer.com and get one there. They have good service and good prices.

[Ruger761]

I'd personally get a Bulldog. I have yet to have one fail on our utility trailers and we lift some heavy loaded trailers with them. They may not be as pretty since they are just painted grey vs galvanized but they hold up. The only issue is most come with a flat foot vs a wheel. Some do have a tube end with a hole to add a wheel to them.

[kasey200]

the f2 on my trailer is a POS. The handle has fallen off and now one of the bevel gears has lost a tooth. i would also find a bulldog.

[JohnZ3]

X2 on the F2. I replaced mine already. Didn't make it through one summer. Expensive POS.

[TeamAllen]

What jack was on there? Was it a Shelby, swivel mount?

Maybe something on this list might work?
http://www.etrailer.com/dept-pg-Trai..._Pull_Pin.aspx

[WakerideN]

X2 on the F2. I replaced mine already. Didn't make it through one summer. Expensive POS.

ditto.. mine is so hard to move up and down.. its internally about ready to cease. just waiting for it to break so I can replace it.

[Timmy!]

I have a Fulton but not the F2. The first one lasted 5 years, I think, so I thought I would just put the same thing back on. They are only like $50-$60 compared to that F2 that is made out of cheap plastic.

[Wickedcummins]

ya they are expensive POS for sure.. Just buy a normal jack Fawk fulton

[Bakes5]

Ok....forget the Fulton. My biggest issue is finding something in the 3.5 x 5 inch bolt pattern range.

[Kimber]

Bakes5 - I had the same problem on my old trailer. I ended up buying a new model and drilling two holes to match my 3.5 x 5 pattern. I had to find one that had a plate with plenty of excess room. I removed the plate, drilled new holes, then I was good to go.

[Timmy!]

Ok....forget the Fulton. My biggest issue is finding something in the 3.5 x 5 inch bolt pattern range.

This one doesn't fit?
http://www.fultonperformance.com/con...t=XP15L%200301

[Bakes5]

^^ I don't think it will. It looks like it won't fit the 3.5" part of my equation. I think I am going to have to go the route of drilling new holes. I will look around locally for something that looks like it can be modified to fit.

I guess the good news is that I am not trying to locate a 2010 tige touch console in 2025.

[chpthril]

I'm pretty sure it is 3.5" x 5". Anybody have a source for a replacement one? I would love to just mount a Fulton f2 up but don't have an adapter plate.

Im guessing thats the mounting plate? If you havent found a replacement with 3.5" x 5" mounting plate after a few google searches, then I would just find one you like and either have it welded on or fab an adapter plate to bolt on the replacement.

[skippabcool]

You may have already seen this thread - http://www.tigeowners.com/forum/show...F2-Fulton-Jack

Have you called or emailed smoothwatersports.com? If yours is different than the one that they have if you give them the dimensions they can probably get you what you need.