Black or White Wetsounds Tower Speakers

[bspot]

I much prefer ther white.

[robert theisen]

I like Chpthril's idea of 2 or 3 color combo as all black tower and speakers is too much black.But everyone likes something different so you should do what you like best.Just look at the different options so you don't have any regrets.Good Luck!

[Robbie Mac.]

Color matched to the boat (is that lime?) or Tuxedo - black pod w/wht nose.

Micheal,

The boat is Sublime, Black, and Frost.
What is your thought with Tuxedo ( just all Black)?

[chpthril]

Micheal,

The boat is Sublime, Black, and Frost.
What is your thought with Tuxedo ( just all Black)?

Cool, how bout black pods with sublime nose.

[lancehon]

Cool, how bout black pods with sublime nose.

That would be sweet

[kko]

I much prefer ther white.

On your setup I think the white looks good. But on the boat in question I dont. But again I am not cutting the check for either of them so what do I know.
Black with green rings is the deal-eo on this boat IMPO.

[wakemongrel]

I'd go with black and then get the Wet Sounds LED Speaker Rings in green. Make sure you get the rings from Wet Sounds, as all the other rings from other copycat makers suck.

[wakemongrel]

Black Wtih Green Wet Sounds Leds

Black Wtih Green Wet Sounds Leds

[bspot]

Are the leds on all the time or can you switch them off?

[Robbie Mac.]

Are the leds on all the time or can you switch them off?

There are four wires in the harness for the new Wetsounds Rev8's and Rev10's. Two for the speakers and two for the LED lights that are an option for those speakers. I don't know what Tige is running the wires to if anything ??? I was just going to run the speaker LED lighting to the white ancher light on the tower. It could just as easily be run down the tower to the switch pannel ( if your into running wires in the tower).
Wetsounds has also said that there is/are LED light collers coming for the XS-65 and XS-650 boat speakers that are used in the hull of the boat.

[Wakeman22]

Black all the way. Sweet set up.

[chpthril]

Are the leds on all the time or can you switch them off?

The speaker and LED is wired separately. You need to run a 2 conductor for the single color or a 4 conductor for the RGB LEDs and then they will be switched with their own power source. Single color you can just switch and the RGB needs a controller.

There are four wires in the harness for the new Wetsounds Rev8's and Rev10's. Two for the speakers and two for the LED lights that are an option for those speakers. I don't know what Tige is running the wires to if anything ??? I was just going to run the speaker LED lighting to the white ancher light on the tower. It could just as easily be run down the tower to the switch pannel ( if your into running wires in the tower).
Wetsounds has also said that there is/are LED light collers coming for the XS-65 and XS-650 boat speakers that are used in the hull of the boat.

The fixed clamp and Alpha mounts do not come pre-wired for LEDs, but its not hard. I just installed the rings and wired my REV-10's with RGB's today. For the TC-3 swivel, there is a 6-pin adapter that is needed.

The in-boats rings are coming soon and the REV-8 and 10 rings are ready to go right now. Wet Sounds offer red, blue, white and RGB.

IIRC, the Alpha-Z tower is prewired for speakers, but a harness would need to be fished for LEDs

[Nobody]

Nobody voted Black.

[Boatman_FX4]

The speaker and LED is wired separately. You need to run a 2 conductor for the single color or a 4 conductor for the RGB LEDs and then they will be switched with their own power source. Single color you can just switch and the RGB needs a controller.



The fixed clamp and Alpha mounts do not come pre-wired for LEDs, but its not hard. I just installed the rings and wired my REV-10's with RGB's today. For the TC-3 swivel, there is a 6-pin adapter that is needed.

The in-boats rings are coming soon and the REV-8 and 10 rings are ready to go right now. Wet Sounds offer red, blue, white and RGB.

IIRC, the Alpha-Z tower is prewired for speakers, but a harness would need to be fished for LEDs

Im about to order my rev 10s and wire them up but i don't recall my alpha z tower having been pre wired??? Are they all like this and should be?

[CoreyZ1]

It should be pre-wired, however mine was bridged at base of tower. Had to split apart to run a 4 channel.


Sent from my iPhone using Tapatalk